Axis-communications 250S Manual do Utilizador Página 23
- Página / 57
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
AXIS 250S User’s Manual Operating the AXIS 250S
23
Exactly how much pre-trigger recording will be produced depends mainly on the bit rate
setting. A high-quality video stream will occupy more of the internal memory and thus
shorten the duration of the recording. The length of the pre-trigger recording in seconds
can be roughly calculated by dividing 16 by the bit rate in Mbit/s.
Important!
Audio
The AXIS 250S provides a fully synchronized audio stream at up to CD quality. The
following settings are available:
• Quality - Select the bit rate and sample rate to use. Generally speaking, the higher the setting,
the better the sound quality, but at the higher levels the difference might not be audible. The
default value (128 kbps) provides good quality sound.
• Volume Settings - The Master volume control should not normally need any adjustment. How-
ever, if you are using some other audio input device on the Line connector, and the audio level
is not satisfactory, then this level may need to be changed. Configurable between -30 and 30
dB.
• Mic input sensitivity - This setting should be set according to the specifications for the con-
nected microphone. If the correct setting is used, there will be no need to adjust the Master
volume level. The volume slider in the web interface will suffice for raising or lowering the vol-
ume when viewing the video stream. If you are unsure of the correct setting for your micro-
phone, try both settings.
• Audio Input - Select the input to use for the audio input. The options are:
• Line - connects other audio input devices
• Mic - connects a standard microphone
Port Status & Devices
Port Status
Clicking this link will display a list showing the status for the 4 inputs and the 1 output.
The inputs cannot be configured here - this must be done from the System options, which
requires administrator access.
If an input or the output has not been enabled by the administrator, then the port will be
shown as “Not in use”.
Note that pre-trigger recording must be enabled in the video settings if you wish to use
pre-trigger recording in event types.
- AXIS 250S MPEG-2 Video Server 1
- AXIS COMMUNICATIONS 2
- Table Of Contents 3
- AXIS 250S User’s Manual 4
- Introduction 5
- Applications 7
- Product Description 8
- Hardware Inventory 9
- Installing the AXIS 250S 10
- Client System Requirements 11
- Operating the AXIS 250S 14
- Access from a browser 15
- The Live View Page 15
- Disconnected Video Source 16
- Configuring Event Types 17
- Setting up a new event type 17
- General 18
- Respond to Trigger 18
- Trigger Type 18
- When Triggered 19
- Adding an Upload Server 20
- HTTP Notification 21
- Audio & Video Settings 22
- Port Status 23
- Preset position setup 24
- Live View Layout 25
- Accessing The System Options 26
- System Options Overview 27
- Adding Users 28
- Editing and Deleting Users 28
- Adding Allowed IP Addresses 28
- Current Server Time 29
- New Server Time 29
- Automatic IP Configuration 30
- Manual IP Configuration 31
- Network Traffic 32
- IO Ports 32
- COM-Port 33
- The Factory Default Settings 34
- Using the AXIS IP Installer 35
- Appendix B - Troubleshooting 37
- PINGing Your IP Address 38
- Obtaining Updated firmware 41
- Updating the firmware 41
- Modifying the File System 42
- Configuration via FTP 42
- Customizing Procedures 43
- Creating a New Home Page 45
- Appendix E - Unit Connections 46
- Connecting Pan/Tilt Devices 48
- Transistor Output 49
- Digital Inputs 49
- Input1=0 50
- Input2=1 50
- Input3=0 50
- Input4=0 50
- Appendix G - Bandwidth 53
- Other Considerations 54
Asus P4B manuales
Manuales del propietario y guías del usuario para Madre De Los Servidores / Estaciones De Trabajo Asus P4B.
Ofrecemos 1 manuales en pdf Asus P4B para descargar gratis por tipos de documentos: Guía de usuario
Comentários a estes Manuais